How to Install your Ring Alarm Sensors on Different Types of Doors, Windows, and Trim

There are many ways to build and decorate a home. That means that the type of doors, windows, and trims in the home will be different from house to house. Having certain types of these home accessories will require you to install your Alarm sensors in specific ways.

The following article will give you some advice on the best ways of installing contact sensors on different types of doors, windows, and trims. There are four general thing to keep in mind, though, regardless of the type of installation you’re doing:

  • The Ring Contact Sensor has two main parts: the sensor, and the magnet it senses.
  • For reliability, ensure that the notches on the sensor and magnet are aligned.

IMG_20180722_133714_revised.jpg

  • Make sure the sensor and magnet will be no more than 1/2" (1.27cm) apart.

IMG_0272_revised.jpg

  • For a long-lasting bond without screw holes, use the included adhesive tape. For the most solid connection, use the included screws.

IMG_7703_revised.jpg

  • Always clean the installation area first to ensure a strong bond.

20181016_192111_revised.jpg

Click on which one you want advice about and scroll down until you find the one you have in your home.

Doors

 

Door Type: Panel

Recommended number of sensors: 1

Best options for installation: The basic flat panel door is the easiest type of door to install sensors on. Simply install the sensors along the top casing or head jamb of the door and make sure their grooves are aligned with one another when the door is closed.

Installation considerations: The fact that the flat panel door is usually the easiest to install a sensor on doesn't mean there are no potential difficulties. The following lists the most common considerations for flat panel doors:

  • Be sure to install your sensor in such a way that it doesn't get knocked off when the door opens.
  • Make sure that the sensor and magnet will be no more than ½ inch apart.
  • Depending on how the door hangs on the wall, it may be impossible to install the magnet and sensor flush with one another.
  • Weatherstripping on the door or casing may make it impossible to find a place to stick on the sensor.

Door Type: Flush

Recommended number of sensors: 1

Best options for installation: Like the panel door, you shouldn't have too much trouble installing a sensor on a flush door. Just install the sensor along the top casing and head jamb or along the side casing and the side jamb.

Installation considerations: The major consideration for this type of door comes about because of trim choices. No trim, no problem. If you do have a trim, see the trim advice below.  

  • Be sure to install your sensor in such a way that it doesn't get knocked off when the door opens.

Door Type: French

Recommended number of sensors: 2

Best options for installation: The unusual way French doors open brings up new considerations. First, you'll need one sensor for each door. The best place to put them is along the gap between the doors. At a pinch, you can also install them along the top casing and head jamb.

Installation considerations: French doors can make for a unique contact sensor installation. The following lists the most common considerations for french doors:

  • Be sure to install your sensor in such a way that it doesn't get knocked off when a door opens.
  • Be sure to name your sensor in the Ring app according to which door it is installed on. This will eliminate confusion.
  • Depending on how the door hangs on the wall, it may be impossible to install the magnet and sensor flush with one another.

Door Type: Pocket

Recommended number of sensors: 1

Best options for installation: We've listed one sensor for this type of door, but the truth is that it's extremely difficult to install traditional contact sensors along this type of door. If you must try, the best place to do it is along the side casing and side jamb.

Installation considerations: If you have pocket doors, you may find the way that traditional contact sensors are installed can make it impossible to install them on pocket doors. Pocket doors really need recessed door sensors.

Door Type: Bypass

Recommended number of sensors: 1

Best options for installation: As long as you put the sensor on the inside door, you shouldn't have a problem installing a sensor on a bypass door. Just place it in the gap between the first door and the top casing/head jamb.

Installation considerations: Remember, you won't be able to install your sensor on the outer door. Otherwise, the following lists the most common considerations for bypass doors:

  • Be sure to install your sensor in such a way that it doesn't get knocked off when a door opens
  • Depending on how the door hangs on the wall, it may be impossible to install the magnet and sensor flush with one another.

Door Type: Bifold

Recommended number of sensors: 1 or 2 (one per door)

Best options for installation: For bifold doors, your best bet is to place the sensor along the gap between the doors or along the top casing/head jamb.

Installation considerations: The biggest consideration with bifold doors is that they have a tendency to shift over time. Keep an eye on the position of the sensors and adjust if you find they're beginning to drift apart. Otherwise, the following lists the most common considerations for bypass doors:

  • Be sure to install your sensor in such a way that it doesn't get knocked off when a door opens
  • Depending on how the door hangs on the wall, it may be impossible to install the magnet and sensor flush with one another.
  • Try installing the contact sensor using double-sided tape rather than a screw. This will allow you to move the sensor over time.
Windows

 

Windows Type: Single-Hung

Recommended number of sensors: 

Best options for installation: Single-hung windows are almost ideally configured for Alarm sensors. Simply install them along the top casing/head jamb or along the side casing/side jamb.

Installation considerations: Ideally you should have no problems installing a sensor onto a single-hung window. That said, you may find an issue depending on your trim choices.

Windows Type: Double-Hung

Recommended number of sensors: 1 or 2

Best options for installation: Double-hung windows offer you a lot of options when it comes to installing a sensor depending on whether the window only opens from the bottom or both the top and bottom panes open. Try along the top casing/head jamb, along the side casing/side jamb, or in the middle between the two panes.

Installation considerations: Be careful when installing the sensor that it doesn't come off when either of the window panes is opened. Depending on how the window is built, it may also be difficult to get the sensor and magnet to properly line up with one another.

Windows Type: Casement

Recommended number of sensors: 1 per pane

Best options for installation: Like double-hung windows, casement windows will need a separate sensor for each window pane. Try putting your sensors along the gap between the window and along the top casing/head jamb.

Installation considerations: Be careful when installing the sensor that it doesn't come off when the window panes are opened. Depending on how the window is built, it may also be difficult to get the sensor and magnet flush against one another.

Windows Type: Slider

Recommended number of sensors: 

Best options for installation: Ideally, you should be able to install the sensors along the gap between the first window and the top casing/head jamb. 

Installation considerations: It's important to understand that you won't have enough room to install the sensor on the back window. It may also be difficult to install the sensor in such a way the sensor doesn't get knocked off when the window opens. It may also be difficult to get the sensor and the magnet flush together. 

Windows Type: Awning

Recommended number of sensors: 

Best options for installation: Given the way awning windows open, your best bet for installation is to put the sensor along the bottom casing/sill. Failing that, try along the side casing/side jamb.

Installation considerations: Depending on how the window opens, it may be difficult to install the sensor in such a way that it doesn't get knocked off when the window opens.

Windows Type: Hopper

Recommended number of sensors: 

Best options for installation: Given the way hopper windows open, your best bet for installation is to put the sensor along the top casing/jamb. Failing that, try along the side casing/side jamb.

Installation considerations: Depending on how the window opens, it may be difficult to install the sensor in such a way that it doesn't get knocked off when the window opens.

Windows Type: Center-pivot

Recommended number of sensors: 

Best options for installation: Center-pivot windows are actually one of the easiest types of windows to install sensors on. You can put sensors along the top casing/head jamb, the bottom casing/sill, or along the side casing/jamb.

Installation considerations: None, really. Most people should have no problem installing a sensor in a center-pivot window.

Windows Type: Jalousie

Recommended number of sensors:

Best options for installation: None. The unique construction of a jalousie window would require a lot of extra work to install a sensor. It's not recommended to even try. Try installing a motion sensor instead.

Installation considerations: Rather than trying to install a contact sensor, you can get the same effect by using a motion detector instead.

 

Trims 

 

Trim Type: Colonial

There is a large variety of trim types that can be broadly termed "Colonial." Most of them involve several layers separated by curved sections. If one of the layers is broad and flat enough to house a sensor, you're in luck. Otherwise, you're better off trying somewhere on the window itself.

Trim Type: Craftsman

There are a large variety of options available in Craftsman trim. Unlike Colonial though, Craftsman trim tends to be fairly flat. Unless your Craftsman trim is unusually elaborate, you should have no problem mounting a sensor on the trim.

Trim Type: Ranch

Ranch trims are excellent candidates for mounting a sensor since ranch-style trims tend to be unfussy with minimal details and curves. That being said, watch out for the occasional sharp angles on some ranch trim that may make it tougher than usual to mount.

Trim Type: Provincial

Provincial trim has a lot of curves and scalloping that will make it difficult to mount a sensor on. In addition, the detail work on provincial trim makes the sensor very obvious and aesthetically unappealing.

Trim Type: Brickmould

Brickmould adds some depth around the window, which may make it difficult to install the sensor and magnet. It's best to install the sensor and magnet perpendicular to each other, with one part on the sill or side jamb and the other part flat on the window casing.

Trim Type: Flat

A flat casing is ideal for installing a sensor. You shouldn't have any trouble with installation on a flat trim.

Was this article helpful?
5 out of 8 found this helpful

Send Feedback